vEdge 100wm routers include a wireless LAN (WLAN) radio for providing access point (AP) functionality for teleworkers, small offices, stores, and branch offices. You can configure the radio to operate at either 2.4 GHz or 5 GHz. In 2.4-GHz mode, the radio can support IEEE 802.11b, 802.11g and 802.11n clients, and in 5-GHz mode, the radio can support IEEE 802.11a, 802.11n and 802.11ac clients. vEdge100wm routers support 3x3 MIMO with three spatial streams, and they use an internal antenna. For WLAN security, you can use preshared key and RADIUS server–based methods.
This article describes how to configure the WLAN interfaces. To configure IEEE 802.11i authentication for the VAPs, see Configuring IEEE 802.1X and IEEE 802.11i Authentication.
On a vEdge100wm router, you can configure up to four service set identifiers (SSIDs) on the WLAN radio. Each SSID is referred to by a virtual access point (VAP) interface. To a client, each VAP interface appears as a different access point (AP) with its own SSID. To provide access to different networks, you can assign each VAP to a different VLAN.
To configure a VAP interface that autoselects its channel and uses no authentication and no encyrption, create a VAP, assign it a number and an SSID, and enable it:
vEdge(config)# wlan radio-band vEdge(config-wlan)# country country vEdge(config-wlan)# interface vapnumber vEdge(config-vap)# no shutdown vEdge(config-vap)# ssid ssid
For the radio band, specify one of the following:
- 2.4GHz—Consists of fourteen 20-MHz channels with overlapping frequency space. The allowable channels and maximum allowed output power are country specific and restricted by regulatory agencies. In the United States and Canada, channels 1, 6 ,and 11 are the only non-overlapping channels. This radio band supports IEEE 802.11b, 802.11g, and 802.11n clients..
- 5GHz—Consists of four 20-MHz channels in UNII-1, four in UNII-2, twelve in UNII-2 Extended, four in UNII-3 and one in ISM band. The allowable channels, their indoor or outdoor usage, and the maximum allowed output power are country specific and are restricted by regulatory agencies. This radio band supports IEEE 802.11a, 802.11n, and 802.11ac clients.
Configuring the country where the router is installed is mandatory, to ensure that the router complies to local regulatory requirements.
For each SSID, configure one VAP interface. number can be from 0 through 3. To reduce RF congestion, it is recommended that you do not configure more than two VAP interfaces on the router.
To activate (enable) the VAP interface, include the no shutdown command.
Each VAP has an SSID. For ssid, enter the name of the SSID. It can be a string from 4 through 32 characters. The SSID must be unique.
By default, a maximum of 25 clients can connect to a single VAP. You can change the maximum number of clients to a value from 1 through 50:
vEdge(config-vap)# max-clients number
It is recommended that you do not configure more than 50 clients across all the VAPs.
Configure Radio-Specific Parameters
For each radio band, you can configure radio-specific parameters.
Specify the country where the router is installed. This configuration is mandatory and ensures that the router complies to local regulatory requirements, and it enforces country-specific allowable channels and maximum allowed output power. By default, the country is the United States. To set a different country, specify the country where the router is installed:
vEdge(config-wlan)# country country
You can use the Viptela wireless router software for the following countries: Australia, Austria, Belgium, Brazil, Bulgaria, Canada, China, Costa Rica, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Italy, Japan, Latvia, Liechtenstein, Lithuania, Luxembourg, Malaysia, Malta, Mexico, Netherlands, New Zealand, Norway, Pakistan, Panama, Philippines, Poland, Portugal, Puerto Rico, Romania, Saudi Arabia, Singapore, Slovakia, Slovenia, South Africa, South Korea, Spain, Sri Lanka, Sweden, Switzerland, Taiwan, Thailand, Turkey, United Kingdom, United States, and Vietnam.
Note: Check the release notes for your software release to determine the countries in which the vEdge 100wm router is certified.
By default, the best radio channel is selected automatically. To explicitly configure automatic channel selection, use the following command:
vEdge(config-wlan)# channel auto
To configure automatic channel selection that excludes channels with dynamic frequency selection (DFS) capabilities, use the following command:
vEdge(config-wlan)# channel auto-no-dfs
To explicitly configure the radio channel to use:
vEdge(config-wlan)# channel channel
For 2.4-GHz WLANs, the channel can be 1 through 13, depending on the country configuration.
For 5-GHz WLANs, the channel, including DFS channels, can be one of 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 144, 149, 153, 157, 161, and 165, depending on the country configuration.
Note: Airport radar uses frequencies that overlap DFS channels. If you are using a 5-GHz radio band, and if your installation is near an airport, it is recommended that you configure channel auto-no-dfs, to remove DFS channels from the list of available channels.
By default, 2.4-GHz radio bands are allocated a channel bandwidth of 20 MHz, and 5-GHz radio bands have a channel bandwidth of 80 MHz. You can set the bandwidth to 20, 40, or 80 MHz:
vEdge(config-wlan)# channel-bandwidth megahertz
The guard interval is the time between symbol transmissions on the WLAN. For 2.4-GHz radio frequencies, the default guard interval is 800 nanoseconds (which is the normal guard interval), and for 5-GHz frequencies it is 400 nanoseconds (which is the short guard interval). These are the only two guard intervals available. The short guard interval can increase throughput, but it can also increase the error rate because of increased sensitivity to RF reflections. You can choose to configure the guard interval explicitly:
vEdge(config-wlan)# guard-interval nanoseconds
Configure a Bridging Domain and IRB
To provide the SSIDs access to different networks, you can assign each VAP to a different VLAN. To do this, create one bridge domain with an untagged VLAN for each SSID:
vEdge(config)# bridge number vEdge(config-bridge)# interface vapnumber vEdge(config-vap)# no native-vlan vEdge(config-vap)# no shutdown
To allow data traffic to be passed among different VLANs, you create an integrated routing and bridging (IRB) logical interface in a VPN domain that connects to the bridging domain:
vEdge(config)# vpn vpn-id vEdge(config-vpn)# interface irbnumber vEdge(config-irb)# ip address prefix/length vEdge(config-irb)# no shutdown
Configure a DHCP server on the IRB interface so that clients connecting to the VLAN can receive IP addresses in the VLAN:
vEdge(config-irb)# dhcp-server vEdge(config-dhcp-server)# address-pool prefix/length vEdge(config-dhcp-server)# admin-state (down | up) vEdge(config-dhcp-server)# options vEdge(config-options)# default-gateway ip-address
WLAN Interface Configuration Example
The configuration example in this section shows how to configure two SSIDs on a WLAN router. One SSID is called CorporateNetwork, and the second is called GuestNetwork.
First, configure the WLAN radio band, and within it, create two VAP interfaces, one for each SSID:
wlan 5GHz country "United States" interface vap0 ssid CorporateNetwork data-security wpa/wpa2-enterprise radius-server radius_server1 max-clients 30 no shutdown ! interface vap1 ssid GuestNetwork data-security wpa/wpa2-personal wpa-personal-key GuestPassword max-clients 10 no shutdown ! !
The CorporateNetwork SSID uses wpa/wpa2-enterprise data security, which works in conjunction with a RADIUS authentication server. Here is the configuration for the RADIUS server:
system radius server 10.20.24.15 acct-port 0 tag radius_server1 vpn 1 secret-key radiusSecretKey exit ! !
Next, configuring two bridging domains, one for each VAP interface (that is, one for each SSID):
bridge 1 interface vap0 no native-vlan no shutdown ! ! bridge 2 interface vap1 no native-vlan no shutdown ! !
Finally, configure IRB interfaces and the DHCP server. Here, the SSID CorporateNetwork uses VPN 1, and the GuestNetwork uses VPN 100:
vpn 1 name "Corporate Network" interface irb1 ip address 10.30.30.1/24 no shutdown dhcp-server address-pool 10.30.30.0/24 offer-time 600 lease-time 86400 admin-state up options default-gateway 10.30.30.1 dns-servers 22.214.171.124 ! ! ! ! vpn 100 name "Guest Network" interface irb2 ip address 192.168.30.1/24 no shutdown dhcp-server address-pool 192.168.30.0/24 offer-time 600 lease-time 86400 admin-state up options default-gateway 192.168.30.1 dns-servers 126.96.36.199 ! ! ! ip route 0.0.0.0/0 vpn 0 !